[[File:SA ADC block diagram.png|thumb|300px|Successive-approximation ADC block diagram showing digital-to-analog converter (DAC), end of conversion indicator (EOC), successive approximation register (SAR), sample and hold circuit (S/H), input voltage ( Vin ) and reference voltage ( Vref )]] A successive-approximation ADC is a type of analog-to-digital converter (ADC) that converts a continuous analog waveform into a discrete digital representation using a binary search through all possible quantization levels before finally converging upon a digital output for each conversion.

Algorithm

The successive-approximation analog-to-digital converter circuit typically consists of four chief subcircuits: Vin . Vin to the output of the internal DAC and outputs the result of the comparison to the successive-approximation register (SAR). Vin to the internal DAC. Vref , supplies the comparator with an analog voltage equal to the digital code output of the SARin . The successive approximation register is initialized so that the most significant bit (MSB) is equal to a digital 1. This code is fed into the DAC, which then supplies the analog equivalent of this digital code (Vref/2) into the comparator circuit for comparison with the sampled input voltage. If this analog voltage exceeds Vin , then the comparator causes the SAR to reset this bit; otherwise, the bit is left as 1. Then the next bit is set to 1 and the same test is done, continuing this binary search until every bit in the SAR has been tested. The resulting code is the digital approximation of the sampled input voltage and is finally output by the SAR at the end of the conversion (EOC). Mathematically, let Vin = xVref , so x in [−1, 1] is the normalized input voltage. The objective is to approximately digitize x to an accuracy of 1/2n. The algorithm proceeds as follows: x0 = 0 . ith approximation xi = xi−1 − s(xi−1 − x)/2i , where, s(x) is the signum function ( sgn(x) = +1 for x ≥ 0 , −1 for x < 0 ). It follows using mathematical induction that . As shown in the above algorithm, a SAR ADC requires: Vin . Vref to normalize the input. ith approximation xi to a voltage. s(xi − x) by comparing the DAC's voltage with the input voltage. xi−1 − s(xi−1 − x)/2i .

Examples

Example 1: The ten steps to converting an analog input to 10 bit digital, using successive approximation, are shown here for all voltages from 5 V to 0 V in 0.1 V iterations. Since the reference voltage is 5 V, when the input voltage is also 5 V, all bits are set. As the voltage is decreased to 4.9 V, only some of the least significant bits are cleared. The MSB will remain set until the input is one half the reference voltage, 2.5 V. The binary weights assigned to each bit, starting with the MSB, are 2.5, 1.25, 0.625, 0.3125, 0.15625, 0.078125, 0.0390625, 0.01953125, 0.009765625, 0.0048828125. All of these add up to 4.9951171875, meaning binary 1111111111, or one LSB less than 5. When the analog input is being compared to the internal DAC output, it effectively is being compared to each of these binary weights, starting with the 2.5 V and either keeping it or clearing it as a result. Then by adding the next weight to the previous result, comparing again, and repeating until all the bits and their weights have been compared to the input, the result, a binary number representing the analog input, is found. Example 2: The working of a 4-bit successive approximation ADC is illustrated below. The MSB is initially set to 1 whereas the remaining digits are set to zero. If the input voltage is lower than the value stored in the register, on the next clock cycle, the register changes its value to that illustrated in the figure by following the green line. If the input voltage is higher, then on the next clock cycle, the register changes its value to that illustrated in the figure by following the red line. The simplified structure of this type of ADC that acts on 2n volts range can be expressed as an algorithm: The successive approximation ADC can be alternatively explained by first uniformly assigning each digital output to corresponding ranges as shown. It can be seen that the algorithm essentially divides the voltage range into two regions and checks which of the two regions the input voltage belongs to. Successive steps involve taking the identified region from before and further dividing the region into two and continuing identification. This occurs until all possible choices of digital representations are exhausted, leaving behind an identified region that corresponds to only one of the digital representations.

Variants

±1/2 LSB to the analog input which is to be converted to binary digital form.

Charge-redistribution successive-approximation ADC

One of the most common implementations of the successive-approximation ADC, the charge-redistribution successive-approximation ADC, uses a charge-scaling DAC. The charge-scaling DAC simply consists of an array of individually switched binary-weighted capacitors. The amount of charge upon each capacitor in the array is used to perform the aforementioned binary search in conjunction with a comparator internal to the DAC and the successive-approximation register. VOS . This step provides automatic offset cancellation (i.e. the offset voltage represents nothing but dead charge, which can't be juggled by the capacitors). Vin . The capacitors now have a charge equal to their respective capacitance times the input voltage minus the offset voltage upon each of them. −Vin . Vref , which corresponds to the full-scale range of the ADC. Due to the binary-weighting of the array, the MSB capacitor forms a 1:1 charge divider with the rest of the array. Thus, the input voltage to the comparator is now −Vin + Vref/2 . Subsequently, if Vin is greater than Vref/2, then the comparator outputs a digital 1 as the MSB, otherwise it outputs a digital 0 as the MSB. Each capacitor is tested in the same manner until the comparator input voltage converges to the offset voltage, or at least as close as possible given the resolution of the DAC.

Use with non-ideal analog circuits

When implemented as an analog circuit – where the value of each successive bit is not perfectly 2N (e.g. 1.1, 2.12, 4.05, 8.01, etc.) – a successive-approximation approach might not output the ideal value because the binary search algorithm incorrectly removes what it believes to be half of the values the unknown input cannot be. Depending on the difference between actual and ideal performance, the maximal error can easily exceed several LSBs, especially as the error between the actual and ideal 2N becomes large for one or more bits. Since the actual input is unknown, it is therefore very important that accuracy of the analog circuit used to implement a SAR ADC be very close to the ideal 2N values; otherwise, it cannot guarantee a best match search.