The Honda H engine was Honda's larger high-performance engine family from the 1990s and early 2000s. It is largely derived from the Honda F engine with which it shares many design features. Like Honda's other 4-cylinder families of the 1980s and 1990s, It has also enjoyed some success as a racing engine, forming the basis of Honda's touring car racing engines for many years, and being installed in lightweight chassis (such as the Honda CR-X) for use in drag racing. The F20B is a part of the F-series family of engines; it is basically a cast-iron sleeved down destroked version of the H22A. It was developed by Honda to be able to enter into the 2-liter class of international racing. H-Series consisted of two different displacements; H22 2157 cc and H23 2259 cc. Both versions were using the same block; different crankshafts and connecting rods were utilized to achieve displacement variation.

DOHC engines

H22

The H22 debuted in the U.S. in 1993 as the H22A1 for use in the Honda Prelude VTEC. Since then, versions of the H22 would become the Prelude's signature high-performance engine worldwide until the end of Prelude production in 2001. In 1994, Honda of Europe used the H22A cylinder head and the H22A engine block as the Formula 3 engine which was an H22A engine destroked from 2.2 liters to 2.0 liters (F3-2000cc) to compete in the European F3 series. It was then used by Mugen Motorsports as the F20B(MF204B) from 1997-2001. In 1995-1997, Honda of Europe used the same H22A-based F3 engine in the British Touring Car Championship (BTCC) Honda Accord. Also, in 1996-1997 Honda of Japan used the same H22A-based F3 engine in the Japan Touring Car Championship (JTCC) Honda Accord and won the JTCC for both years. Honda of Europe hired Neil Brown Engineering of England to convert the H22A engine into an F3 engine which would be later used in BTCC and JTCC. The type S Prelude has an engine rev cut of 9100rpm.

Engine Specifications

H22A DOHC VTEC

H22A

H22A1

H22A2

H22A3

H22A4

H22A5

H22A7

H22A8

H22Z1

H23

The H23 was an increased-stroke, non-VTEC version of the H22, used in Japan, North America, and Europe. It shared the same Fiber Reinforced Metal (FRM) cylinder wall liners with the H22. Specifications

H23A1

H23A2

H23A3

H23A DOHC VTEC

In 1998, Honda of Japan produced a rare DOHC VTEC version of the H23A engine for use in Japan only. It has been factory modified with an internal oil passage in the H23A block to operate the VTEC solenoid in the H22A head. It has the same horsepower rating as the H22A engine but a lower redline of 7200rpms because it has a longer stroke than the H22A. The H23A DOHC VTEC has 87x95 mm (bore and stroke) and the H22A DOHC VTEC has 87x90.7 mm (bore and stroke). It also lacked the oil squirters found on the H22A and H22Z VTEC engines, but there are provisions for the oil squirters to be installed, as the main oil galley feeding the squirters has been tapped, the holes for the bolts that hold the squirters at the bottom of each bore have been tapped. Installation of the squirters is possible but the actual squirters need to be bent to clear the larger stroke crank of the H23A VTEC engine. The H23A DOHC VTEC Engine is largest displacement in the H Series engines with a compression ratio of 10.6:1. Below is a chart that consists all of the engines in the H Series.

H Series Motor Specifications Chart 2

H Series Motor Specifications Chart 3